Effects of Cr on the stacking-fault energy (SFE) and damping capacity were investigated by experimental and theoretical methods. The effect of Cr on SFE was thermodynamically calculated; the damping capacity, phase composition, microstructure and corrosion resistance were experimentally measured. The results showed that Cr increases the SFE of Fe17MnxCr which resulted in the decay of damping capacity; the increase in α’ martensite with the increasing Cr content above 6% pins the movement of Shockley partials’ dislocation and thus makes the damping capacity even worse; the optimum Cr content of Fe17MnxCr to improve the corrosion resistance in water vapour with a lesser decrease in damping capacity is about 6%.
VitekJ. M. and WarlimontH.: ‘On a metastable miscibility gap in gamma-Mn-Cu alloy and the origin of their high damping capacity’, Metal Sci., 1976, 10, (1), 7–13. doi: 10.1179/030634576790431426
2.
LinH. C., WuS. K. and YehM. T.: ‘Damping characteristics of TiNi shape memory alloys', Metall. Trans. A, 1993, 24, (10), 2189–2194. doi: 10.1007/BF02648593
3.
RitchieI. G. and PanZ. L.: ‘High-damping metals and alloys', Metall. Trans. A, 1991, 22, (3), 607–616. doi: 10.1007/BF02670281
4.
KimJ. C., BaikS. H., JunJ. H., LeeY. K.: ‘Effect of chromium addition on damping capacity, mechanical property, and corrosion resistance of Fe-18% Mn alloy’, Key Eng. Mater., 2006, 319, 73–78. doi: 10.4028/www.scientific.net/KEM.319.73
5.
HuangS. K., LiN., WenY. H., TengJ., DingS. and XuY. G.: ‘Effect of Si and Cr on stacking fault probability and damping capacity of Fe–Mn alloy’, Mater. Sci. Eng. A, 2008, 479, (1), 223–228. doi: 10.1016/j.msea.2007.06.063
6.
LeeY. K., BaikS. H., KimJ. C. and ChoiC. S.: ‘Effects of amount of ε martensite, carbon content and cold working on damping capacity of an Fe–17% Mn martensitic alloy’, J. Alloy. Compd., 2003, 355, (1), 10–16 doi: 10.1016/S0925-8388(03)00244-5
7.
JeeK. K., ItoK. and ShinM. C.: ‘Damping capacity in Fe-27Mn-3.5Si alloy.’, ISIJ Int., 1994, 34, (11), 912–916. doi: 10.2355/isijinternational.34.912
8.
LeeY. K., JunJ. H. and ChoiC. S.: ‘Effect of ε martensite content on the damping capacity of Fe17Mn alloy’, Scripta Mater., 1996, 35, (7), 835–830. doi: 10.1016/1359-6462(96)00231-X
9.
JeeK. K., JangW. Y., BaikS. H. and ShinM. C.: ‘Damping mechanism and application of Fe-Mn based alloys', Mater. Sci. Eng. A, 1999, 273–275, (99), 538–542. doi: 10.1016/S0921-5093(99)00395-0
10.
LeeY. K., JunJ. H. and ChoiC. S.: ‘Damping capacity in Fe-Mn binary Alloys', ISIJ Int., 1997, 37, (10), 1023–1030. doi: 10.2355/isijinternational.37.1023
11.
JunJ. H. and ChoiC. S.: ‘The influence of Mn content on microstructure and damping capacity in Fe–(17∼ 23)% Mn alloys', Mater. Sci. Eng. A, 1998, 252, (1), 133–138. doi: 10.1016/S0921-5093(98)00648-0
12.
JunJ. H., BaikS. H., LeeY. K. and ChoiC. S.: ‘The influence of aging on damping capacity of Fe-17%Mn-X%C alloys', Scripta Mater., 1998, 39, (1), 39–44 doi: 10.1016/S1359-6462(98)00125-0
13.
JunJ. H., LeeY. K., KimJ. M., KimK. T. and JungW. J.: ‘Influences of Si and Co addition on microstructure and damping capacity of Fe-Mn Alloy’, Key Eng. Mater., 2006, 319, 85–90. doi: 10.4028/www.scientific.net/KEM.319.85
14.
WatanabeY., SatoH., NishinoY. and KimI. S.: ‘Training effect on damping capacity in Fe–20mass% Mn binary alloy’, Mater. Sci. Eng. A, 2008, 490, (1), 138–145. doi: 10.1016/j.msea.2008.01.038
15.
WatanabeY., SugaY., SatoH. and TsukamotoH.: ‘Damping capacity of Fe–17mass% Mn high damping alloy with variant controlled Microstructure’, Mater Trans., 2013, 54, (8), 1288–1294. doi: 10.2320/matertrans.ME201305
16.
WatanabeY., SatoH., NishinoY. and KimI. S.: ‘Training effects on damping capacity in Fe-Mn and Fe-Mn-Cr alloys', Mater. Sci. Forum, 2010, 638–642, 2201–2206. doi: 10.4028/www.scientific.net/MSF.638-642.2201
17.
KimG. H., NishimuraY., WatanabeY., SatoH., NishinoY., JungH. R., KangC. Y. and KimI. S.: ‘Effects of ε-martensite and dislocations behavior by thermos-mechanical treatment on Fe-Cr-Mn damping alloy’, Mater. Sci. Eng. A, 2009, 521–522, 368–371. doi: 10.1016/j.msea.2008.09.138
18.
StanfordN. and DunneD. P.: ‘Thermo-mechanical processing and the shape memory effect in an Fe-Mn-Si based shape memory alloy’, Mater. Sci. Eng. A, 2006, 422, 352–359. doi: 10.1016/j.msea.2006.02.009
19.
HuangS. K., LiN., WenY. H., TengJ., DingS., XuY. G. and DingS.: ‘Temperature dependence of the damping capacity in Fe–19.35 Mn alloy’, J. Alloy. Compd., 2008, 455, 225–230. doi: 10.1016/j.jallcom.2007.01.147
20.
HuangS. K., HuangW. R., LiuJ. H., TengJ., LiN. and WenY. H.: ‘Internal friction mechanism of Fe–19Mn alloy at low and high strain amplitude’, Mater. Sci. Eng. A, 2013, 560, 837–840. doi: 10.1016/j.msea.2012.10.060
21.
WenY., XiaoH., PengH., LiN. and RaabeD.: ‘Relationship between damping capacity and variations of vacancies concentration and segregation of carbon atom in an Fe-Mn Alloy’, Meter. Meter. Trans. A, 2015, 46, (11), 4828–4833. doi: 10.1007/s11661-015-3111-1
22.
AverbachB. L. and CohenM.: ‘X-ray determination of retained austenite by integrated intensities', Trans. AIME, 1948, 176, 401.
23.
OlsonG. B. and CohenM.: ‘A general mechanism of martensitic nucleation: part II. FCC→ BCC and other martensitic transformations', Mater. Trans. A, 1976, 7, (12), 1905–1914. doi: 10.1007/BF02659823
24.
AllainS., ChateauJ. P., BouazizO., MigotS. and GueltonN.: ‘Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe–Mn–C alloys', Mater. Sci. Eng. A, 2004, 387–389, (1), 158–162. doi: 10.1016/j.msea.2004.01.059
25.
IshidaK.: ‘Direct estimation of stacking fault energy by thermodynamic analysis', Phys. Status Solidi, 1976, 36, (2), 717–728. doi: 10.1002/pssa.2210360233
26.
InderG.: ‘The role of magnetism in the calculation of phase diagrams', Phys. B, 1981, 103, 82–100. doi: 10.1016/0378-4363(81)91004-4
27.
HillertM. and JarlM.: ‘A model for alloying effects in ferromagnetic metals', CALPHAD, 1978, 2, (3), 227–238. doi: 10.1016/0364-5916(78)90011-1
28.
CurtzeS., KuokkalaV. T., OikariA., TalonenJ. and HanninenH.: ‘Thermodynamic modeling of the stacking fault energy of austenitic steels', Acta Mater., 2011, 59, (3), 1068–1076. doi: 10.1016/j.actamat.2010.10.037
29.
DumayA., ChateauJ. P., AllainS., MigotS. and BouazizO.: ‘Influence of addition elements on the stacking-fault energy and mechanical properties of an austenitic Fe–Mn–C steel’, Mater. Sci. Eng. A, 2008, 483–484, 184–187. doi: 10.1016/j.msea.2006.12.170
30.
KingH. W.: ‘An assessment of the Fe-Mn system’, CALPHAD, 1989, 13, (3), 243–252 doi: 10.1016/0364-5916(89)90004-7
31.
JinJ. E., JungM., LeeC. Y., JeongJ. and LeeY. K.: ‘Néel temperature of high Mn austenitic steels', Met. Mater. Int., 2012, 18, (3), 419–423. doi: 10.1007/s12540-012-3006-2
32.
ZhangY. S., LuX., TianX. and QinZ.: ‘Compositional dependence of the Néel transition, structural stability, magnetic properties and electrical resistivity in Fe–Mn–Al–Cr–Si alloys', Mater. Sci. Eng. A, 2002, 334, (1), 19–27. doi: 10.1016/S0921-5093(01)01781-6
33.
KingH. W. and PetersM. A.: ‘Predictive equations for martensitic and antiferromagnetic transformations in fe-mn-al-si alloys', Can. Metall. Quart., 1997, 36, (2), 137–141.
34.
XiongR., PengH., SiH., ZhangW. and WenY.: ‘Thermodynamic calculation of stacking fault energy of the Fe–Mn–Si–C high manganese steels', Mater. Sci. Eng. A, 2014, 598, 376–386. doi: 10.1016/j.msea.2014.01.046
35.
DinsdaleA. T.: ‘SGTE data for pure elements', CALPHAD, 1991, 15, (4), 317–425. doi: 10.1016/0364-5916(91)90030-N
36.
BamptonC. C., JonesI. P. and LorettoM. H.: ‘Stacking fault energy measurements in some austenitic stainless steels'', Acta Metall., 1978, 26, (1), 39–51. doi: 10.1016/0001-6160(78)90200-6
37.
PierceD. T., BentleyJ., JimenezJ. A. and WittigJ. E.: ‘Stacking fault energy measurements of Fe-Mn-Al-Si austenitic twinning-induced plasticity steels', Scripta Mater., 2012, 66, (10), 753–756. doi: 10.1016/j.scriptamat.2012.01.050
38.
XuZ. Y.: ‘Thermodynamics of the martensitic transformation in Fe-X-C systems', Acta Metall. Sin., 1980, 16, (4), 420–425.
39.
BreedisJ. F. and KaufmanL.: ‘The formation of Hcp and Bcc phases in austenitic iron alloys', Metall. Trans., 1971, 2, (9), 2359–2371. doi: 10.1007/BF02814874
40.
JunJ. H. and ChoiC. S.: ‘Variation of stacking fault energy with austenite grain size and its effect on the MS temperature of γ→ ε martensitic transformation in Fe–Mn alloy’, Mater. Sci. Eng. A, 1998, 257, (2), 353–356. doi: 10.1016/S0921-5093(98)00994-0
41.
TomotaY.: ‘Phase-transformation, microstructure and mechanical-behavior in FeMn alloys', Tetsu-to-Hagane, 1991, 77, (3), 315–325.
42.
SöderbergO., LiuX. W., YakovenkoP. G., UlakkoK. and LindroosV. K.: ‘Corrosion behaviour of Fe–Mn–Si based shape memory steels trained by cold rolling’, Mater. Sci. Eng. A, 1999, 273–275, 543–548. doi: 10.1016/S0921-5093(99)00396-2
43.
BliznukV. V., GlavatskaN. I., SöderbergO. and LindroosV. K.: ‘Effect of nitrogen on damping, mechanical and corrosive properties of Fe–Mn alloys', Mater. Sci. Eng. A, 2002, 338, 213–218. doi: 10.1016/S0921-5093(02)00060-6
