The actual service life of wind turbine gearboxes is often well below the desired 20 years. One of the prevalent failure modes in gearbox bearing raceways is white structure flaking (WSF) in as little as 6–24 months of operation by the formation of axial cracks and white etching cracks (WECs) with associated microstructural change called white etching areas (WEAs). Despite these failures having been observed for two decades in various industries, the drivers and mechanisms for their formation are still highly contested. Discussed in this review are methods for searching and analysing WECs, mechanisms for WEA microstructural change, WEC initiation and propagation theories, WSF formation drivers and finally technologies and processes offering resistance to WSF. This updated review serves as a recap, comprehensive update on findings, current focus areas and remaining challenges.
This paper is part of a Themed Issue on Recent developments in bearing steels.
EvansM.-H.: ‘White structure flaking (WSF) in wind turbine gearbox bearings: effects of ‘butterflies’ and white etching cracks (WEC)’, J. Mater. Sci. Technol., 2012, 28, (1), 3–22.
2.
EvansM.-H.: ‘White structure flaking failure in bearings under rolling contact fatigue’, PhD thesis, University of Southampton, 2013.
3.
EvansM.-H., RichardsonA. D., WangL. and WoodR. J. K.: ‘Serial sectioning investigation of butterfly and white etching crack (WEC) formation in wind turbine gearbox bearings’, Wear, 2013, 302, 1573–1582.
4.
EvansM.-H., RichardsonA. D., WangL. and WoodR. J. K.: ‘Effect of hydrogen on butterfly and white etching crack (WEC) formation under rolling contact fatigue (RCF)’, Wear, 2013, 306, (1–2), 226–241.
5.
EvansM.-H., RichardsonA. D., WangL., WoodR. J. K. and AndersonW. B.: ‘Confirming subsurface initiation at non-metallic inclusions as one mechanism for white etching crack (WEC) formation’, Tribol. Int., 2014, 75, 87–97. doi: 10.1016/j.triboint.2014.03.012
6.
EvansM.-H., WalkerJ. C., MaC., WangL. and WoodR. J. K.: ‘A FIB/TEM study of butterfly crack formation and white etching area (WEA) microstructural changes under rolling contact fatigue in 100Cr6 bearing steel’, Mater. Sci. Eng. A, 2013, 570, 127–134. doi: 10.1016/j.msea.2013.02.004
7.
EvansM.-H., WangL., JonesH. and WoodR. J. K.: ‘White etching crack (WEC) investigation by serial sectioning, focused ion beam and 3-D crack modelling’, Tribol. Int., 2013, 65, 146–160. doi: 10.1016/j.triboint.2013.03.022
8.
EvansM.-H., WangL. and WoodR. J. K.: ‘Mechanisms of white etching cracks (WECs) and white etching area (WEA) under rolling contact fatigue’, Proc. Inst. Mech. Eng. J-Eng. Tribol., 2014, 228, (10), 1047–1062. doi: 10.1177/1350650114525363
9.
RichardsonA. D., WangL., WoodR. J. K., EvansM.-H., AndersonW. B. and IngramM.: ‘Investigation of the role of hydrogen in white structure flaking (WSF) of wind turbine gearbox bearings’, STLE annual meeting, Dalas, TX, 2015, STLE.
10.
GegnerJ.: ‘Tribological aspects of rolling bearing failures’, in ‘Tribology-lubricants and lubrication’, (ed. KuoC.-H.), 33–94; 2011, Rijeka, InTech.
11.
GegnerJ. and NierlichW.: ‘Frictional surface crack initiation and corrosion fatigue driven crack growth’, Wind turbine tribology seminar, renaissance boulder flatiron hotel, Broomfield, CO, USA, November 15–17, 2011.
12.
HolwegerW.: ‘Influence on bearing life by new material phenomena’, NREL wind turbine tribology seminar, renaissance boulder flatiron hotel broomfield, CO, USA, November 15–17, National Renewable Energy Laboratory (NREL), 2011.
13.
LuyckxJ.: ‘Hammering wear impact fatigue hypothesis WEC/irWEA failure mode on roller bearings’, Wind turbine tribology seminar, Renaissance Boulder Flatiron Hotel Broomfield, CO, USA, November 15–17, 2011.
14.
TanimotoH., TanakaH. and SugimuraJ.: ‘Observation of hydrogen permeation into fresh bearing steel surface by thermal desorption spectroscopy’, Tribol. Online, 2011, 6, (7), 291–296. doi: 10.2474/trol.6.291
15.
UyamaH.: ‘The mechanism of white structure flaking in rolling bearings’, NREL wind turbine tribology seminar, Renaissance Boulder, Flatiron Hotel, Broomfield, CO, USA, November 15–17, National Renewable Energy Laboratory (NREL), 2011.
16.
CampbellJ., EvansM.-H. and ZaretskyE.: ‘Letter to the editor: correspondence regarding the role of white etching cracks and related features in the failure processes of bearing steels, with responses from the authors’, J. Mater. Sci. Technol., 2012, 28, (11), 1358–1367. doi: 10.1179/0267083612Z.000000000203
KirchheimR. and KirchheimA.: Hydrogen sensor: non-destructive measurement of diffusible hydrogen in metals, in http://www.kirctec.com, KircTec, Editor, 2012.
19.
LewisM. N. and TomkinsB.: ‘A fracture mechanics interpretation of rolling bearing fatigue’, Proc. Inst. Mech. Eng. Part J-Eng. Tribol., 2012, 226, (5), 389–405. doi: 10.1177/1350650111435580
20.
LuyckxJ.: ‘White etching crack failure mode in roller bearings: from observation via analysis to understanding and an industrial solution’, Rolling element bearings, Anaheim, CA, US, 2012, ASTM International, 1–25.
21.
SzostB. A. and Rivera-Díaz-del-CastilloP. E. J.: ‘Unveiling the nature of hydrogen embrittlement in bearing steels employing a new technique’, Scr. Mater., 2012, 68, (7), 467–470. doi: 10.1016/j.scriptamat.2012.11.018
22.
ErrichelloR., BudnyR. and EckertR.: ‘Investigations of bearing failures associated with white etching areas (WEAs) in wind turbine gearboxes’, Tribol. Trans., 2013, 56, (6), 1069–1076. doi: 10.1080/10402004.2013.823531
23.
GrecoA., ShengS., KellerJ. and ErdemirA.: ‘Material wear and fatigue in wind turbine systems’, Wear, 2013, 301, (1–2), 1583–1591. doi: 10.1016/j.wear.2013.01.060
24.
KangJ.-H.: ‘Mechanisms of microstructural damage during rolling contact fatigue of bearing steels’, PhD thesis, University of Cambridge, 2013.
25.
KangJ.-H., HosseinkhaniB., WilliamsC. A., MoodyM. P., BagotcP. A. J. and Rivera-Diaz-del-CastilloP. E. J.: ‘Solute redistribution in the nanocrystalline structure formed in bearing steels’, Scr. Mater., 2013, 69, 630–633. doi: 10.1016/j.scriptamat.2013.07.017
26.
KangJ. H. and Rivera-Díaz-del-CastilloP. E. J.: ‘Carbide dissolution in bearing steels’, Comput. Mater. Sci., 2013, 67, 364–372. doi: 10.1016/j.commatsci.2012.09.022
27.
MauntzM. R., GegnerJ., KuipersU. and KlingauS.: ‘A sensor system for online oil condition monitoring of operating components’ in ‘Tribology-fundamentals and advancements’, (ed. GegnerJ.), 305–321; 2013, Rijeka, InTech.
28.
StadlerK. and StubenrauchA.: Premature bearing failures in wind gearboxes and white etching cracks (WEC) in evolution. 2013, SKF.
29.
SzostB. A., VegterR. H. and Rivera-Díaz-del-Castillo:P. E. J. ‘Developing bearing steels combining hydrogen resistance and improved hardness’, Mater. Des., 2013, 43, 499–506. doi: 10.1016/j.matdes.2012.07.030
30.
WestO. H. E., DiederichsA. M., AlimadadiH., DahlK. V. and SomersM. A. J.: ‘Application of complementary techniques for advanced characterization of white etching cracks’, Pract. Metallogr., 2013, 50, (6), 410–431. doi: 10.3139/147.110246
31.
WinzerN. and KhaderI.: ‘Hydrogen diffusion and trapping in bodies undergoing rolling contact’, Wear, 2013, 303, (1–2), 451–458. doi: 10.1016/j.wear.2013.03.042
BarteldesS., WaltherF. and HolwegerW.: ‘Residual stress evolution and acoustic emission during lubrication-assisted White Etching Crack (WEC) Formation’, 2014 STLE Annual Meeting, Disney's Contemporary Resort, Lake Buena Vista, FL, USA, 2014.
34.
FrankeJ., HolwegerW., SurborgH., BlassT., FahlJ., ElfrathT., AbeT. and MerkD.: ‘Influence of tribolayer on rolling bearing fatigue performed on a FE8 test rig’, TAE 19th international colloquium tribology, Ostfildern, Germany, 2014, 1–13.
35.
GrujicicM., ChennaV., GalgalikarR., SnipesJ. S., RamaswamiS. and YavariR.: ‘Wind-turbine gear-box roller-bearing premature-failure caused by grain-boundary hydrogen embrittlement: a multi-physics computational investigation’, J. Mater. Eng. Perform., 2014, 23, (11), 3984–4001. doi: 10.1007/s11665-014-1188-0
36.
GrujicicM., RamaswamiS., YavariR., GalgalikarR., ChennaV. and SnipesJ. S.: ‘Multiphysics computational analysis of white-etch cracking failure mode in wind turbine gearbox bearings’, Proc. Inst. Mech. Eng. L: J. Mater. Des. Appl., 2014, 1–21.
37.
HolwegerW.: ‘Progresses in solving white etching crack phenoma’, Gearbox reliability collaborative all members meeting, NREL Golden, Colorado, February 10–12, 2014, 2014.
HydeR. S.: ‘White etching areas: importance of microstructural characterization and modeling’, Gearbox reliability collaborative all members meeting, NREL Golden, CO, February 10–12, 2014, 2014.
40.
MoghaddamS. M., SadeghiF., WeinzapfelN. and LiebelA.: ‘A damage mechanics approach to simulate butterfly wing formation around nonmetallic inclusions’, J. Tribol., 2014, 137, (1), 1–13.
41.
RuellanA., VilleF., KleberX., ArnaudonA. and GirodinD.: ‘Understanding white etching cracks in rolling element bearings: the effect of hydrogen charging on the formation mechanisms’, Proc. Inst. Mech. Eng. J-J. Eng. Tribol., 2014, 228, (11), 1252–1265. doi: 10.1177/1350650114522452
42.
Solano-AlvarezW. and BhadeshiaH. K. D. H.: ‘White-etching matter in bearing steel. Part II: distinguishing cause and effect in bearing steel failure’, Metall. Mater. Trans. A, 2014, 45, (11), 4916–4931. doi: 10.1007/s11661-014-2431-x
43.
StadlerK.: ‘Premature wind gearbox bearing failures and white etching cracks (WEC)’, Gearbox reliability collaborative all members meeting, NREL Golden, CO, February 10–12, 2014, 2014.
44.
StadlerK., LaiJ. and VegterR. H.: ‘A review: the dilemma with premature white etching crack (WEC) bearing failures’, J. ASTM Int., 2014, STP 1580, 487–508.
45.
UyamaH. and YamadaH.: White structure flaking in rolling bearings for wind turbine gearboxes. Wind Systems Magazine, 2014. p. 14–25.
46.
GegnerJ. and NierlichW.: ‘Service loading analysis of wind turbine gearbox rolling bearings based on X-ray diffraction residual stress measurements’, Mater. Sci. Forum, 2014, 768–769, 723–732. doi: 10.4028/www.scientific.net/MSF.768-769.723
47.
KonradA., NierlichW. and GegnerJ.: ‘Finite element analysis of the rolling-sliding contact of vibrationally loaded bearings based on a micro friction model’, Mater. Sci. Forum, 2014, 768–769, 714–722. doi: 10.4028/www.scientific.net/MSF.768-769.714
48.
4LinesFusion: 4LinesFusion's SeerWorks Tribology Engine: 4LF-WEC Radar. 2015, London, 4LinesFusion, p. 1–3. Available from: www.4linesfusion.com, accessed 7 January 2016.
49.
4LinesFusion: The 4LinesFusion White Etching Crack (WEC) Coefficient - k4LF. 2015, London, 4LinesFusion, p. 1–3. Available from: www.4linesfusion.com, accessed 7 January 2016.
BhadeshiaH. K. D. H. and Solano-AlvarezW.: ‘Critical assessment 13: elimination of white etching matter in bearing steels’, J. Mater. Sci. Technol., 2015, 31, (9), 1011–1015. doi: 10.1179/1743284715Y.0000000036
52.
BruceT., LongH. and Dwyer-JoyceR. S.: ‘Dynamic modelling of wind turbine gearbox bearing loading during transient events’, IET Renew. Power Gen., 2015, 9, (7), 821–830. doi: 10.1049/iet-rpg.2014.0194
53.
BruceT., RoundingE., LongH. and Dwyer-JoyceR. S.: ‘Characterisation of white etching crack damage in wind turbine gearbox bearings’, Wear, 2015, 338–339, 164–177. doi: 10.1016/j.wear.2015.06.008
54.
DiederichsA. M., SchwedtA., MayerJ. and DreifertT.: ‘Electron microscopy analysis of structural changes within white etching areas’, J. Mater. Sci. Technol., 2015, In Press. DOI: 10.1080/02670836.2016.1139030.
55.
DiederichsA. M., SchwedtA., ParkD., HerbigM. and MayerJ.: ‘Observation of deformation induced redistribution of chromium and carbon in bearing steel’, Microscopy conference 2015, Georg-August-University, Gottingen, Germany, 2015.
56.
GmbHV. U.: Standstills caused by WEC (white etching cracks) reduced by ultrasonic inspection, 2015.
57.
GouldB. and GrecoA. C.: ‘The influence of sliding and contact severity on the generation of white etching cracks’, Tribol. Lett., 2015, 60, (2), 1–13. doi: 10.1007/s11249-015-0602-6
58.
GouldB., GrecoA. C. and PreilserR.: ‘High energy X-ray tomography of failed wind turbine bearings’, STLE annual meeting, Dalas, TX, May 20 2015, 2015.
59.
JanakiramanS., WestO., KlitP. and JensenN. S.: ‘Observations of the effect of varying Hoop stress on fatigue failure and the formation of white etching areas in hydrogen infused 100Cr6 steel rings’, Int. J. Fatigue, 2015, 77, 128–140. doi: 10.1016/j.ijfatigue.2015.03.011
60.
MoghaddamS. M., SadeghiF., PaulsonK., WeinzapfelN., CorrensM., BakolasV. and DinkelM.: ‘Effect of non-metallic inclusions on butterfly wing initiation, crack formation, and spall geometry in bearing steels’, Int. J. Fatigue, 2015, 80, 203–215. doi: 10.1016/j.ijfatigue.2015.05.010
RuellanA.: ‘Tribological analysis of white etching crack (WEC) failures in rolling element bearings’, PhD thesis, INSA de Lyon, 2015.
63.
ŠčepanskisM., JakovičsA., KaldreI., HolwegerW., NackeB. and DiederichsA.: ‘The numerical model of electrothermal deformations of carbides in bearing steel as the possible cause of white etching cracks initiation’, Tribol. Lett., 2015, 59, (2), 1–10. doi: 10.1007/s11249-015-0564-8
64.
StadlerK., HanB., BrizmerV. and PasaribuR.: Benefits of using black oxidized bearings in wind applications, in SKF Evolution. 2015, SKF.
65.
YamadaH. and UyamaH.: ‘The effects of alloy elements and heat treatments on white structure flaking in rolling bearings’, STLE annual general meeting, Dallas, TX, May 17–21, 2015, 2015.
66.
GrecoA. C.: ‘Failure modes and testing methods: advances in white-etch crack research’, STLE tribology frontiers conference, Denver, CO, October 25–27, 2015, 2015, STLE.
67.
BeckerP. C.: ‘Microstructural changes around non-metallic inclusions caused by rolling contact fatigue of ball-bearing steels’, Met. Technol., 1981, 8, 234–243. doi: 10.1179/030716981803275415
68.
GrabulovA., PetrovR. and ZandbergenH. W.: ‘EBSD investigation of the crack initiation and TEM/FIB analyses of the microstructural changes around the cracks formed under rolling contact fatigue (RCF)’, Int. J. Fatigue, 2010, 32, (3), 576–583. doi: 10.1016/j.ijfatigue.2009.07.002
69.
ÖsterlundR., VingsboO., VincentL. and GuiraldenqP.: ‘Butterflies in fatigued ball bearings - formation mechanism and structure’, Scand. J. Metall., 1982, 11, 23–32.
MusialW., ButterfieldS. and McNiffB.: ‘Improving wind tubine gearbox reliability’, EWEA 2007, Milan, Italy, 7–10 May 2007, U.S. Department of Commerce, 1–10.
72.
RosinskiJ. and SmurthwaiteD.: ‘Troubleshooting wind gearbox problems’, in Gear Solutions’, (ed. RogersM. and ConradA. C.), 22–33; 2010, Pelham, AL, Media Solutions, Inc.
73.
HeegeA., RadovcicY. and BetranJ.: Fatigue load computation of wind turbine gearboxes by coupled structural, mechanism and aerodynamic analysis. DEWI Magazine, 2006. p. 61–68.
74.
BurtonT., SharpeD., JenkinsN. and BossanyiE.: ‘Wind energy handbook’; 2001, New York, John Wiley and Sons.
75.
VriesE.: ‘Wind turbine gearboxes and the effort to improve their reliability’, Windpower Monthly 2010 [viewed: 16 June]
76.
RasmussenF., ThomsenK. and LarsenT. J.: ‘The gearbox problem revisited’; 2004, Roskilde, DK, Risø National Laboratory.
77.
BhadeshiaH. K. D. H.: ‘Steels for bearings’, Prog. Mater. Sci., 2012, 57, (2), 268–435. doi: 10.1016/j.pmatsci.2011.06.002
78.
ScottD., LoyB. and MillsG. H.: ‘Metallurgical aspects of rolling contact fatigue’, Proc. Inst. Mech. Eng., 1966, 181, (315), 94–103.
79.
BeswickJ., GabelliA. A., IoannidesS., TrippJ. H. and VoskampA. P.: ‘Rolling bearing life models and steel internal cleanliness’ in ‘Advances in the production and use of steel with improved internal cleanliness’, (ed. MahaneyJ.), 12–31; 1999, West Conshohocken, PA, ASTM.
80.
EckelJ. A., GlawsP. C., WolfeJ. O. and ZorcB. J.: ‘Clean engineered steels-progress at the end of the twentieth century’ in ‘Advances in the production and use of steel with improved internal cleanliness’, (ed. MahaneyJ.), 1–12; 1999, West Conshohocken, PA, USA, ASTM.
81.
WaltonH. W.: ‘The influence of residual stresses on the susceptibility to hydrogen embrittlement in hardened steel components subjected to rolling contact conditions’, SAE international off-highway congress, Las Vegas, NV, March 19–21, 2002, SAE International, 1–6.
82.
SadeghiF., JalalahmadiB., SlackT. S., RajeN. and ArakereN. K.: ‘A review of rolling contact fatigue’, J. Tribol., 2009, 131, (4), 1–15. doi: 10.1115/1.3209132
83.
OlverA.: ‘The mechanism of rolling contact fatigue: an update’, Proc. Inst. Mech. Eng. J-J. Eng. Tribol., 2005, 219, (5), 313–330. doi: 10.1243/135065005X9808
84.
TaoJ., HughesT. G., EvansH. P., SnidleR. W., HopkinsonN. A., TalksM. and StarbuckJ. M.: ‘Elastohydrodynamic lubrication analyses of gear tooth surfaces from micropitting tests’, J. Tribol., 2003, 125, 267–274. doi: 10.1115/1.1510881
85.
VoskampA. P., ÖsterlundR., BeckerP. C. and VingsboO.: ‘Gradual changes in residual stress and microstructure during contact fatigue in ball bearings’, Met. Technol., 1980, 7, (1), 14–21. doi: 10.1179/030716980803286676
86.
ZwirleinO. and SchlichtH.: ‘Rolling contact fatigue mechanisms-accelerated testing versus field performance’ in ‘Rolling contact fatigue testing of bearing steels-ASTM STP 771’, (ed. HooJ. J. C.), 358–379; 1982, West Conshohocken, PA, ASTM International.
87.
VoskampA. P.: ‘Material response to rolling contact loading’, J. Tribol., 1985, 107, 359–366. doi: 10.1115/1.3261078
88.
VoskampA. P.: ‘Fatigue and material response in rolling contact’ in ‘Bearing steels: into the 21st Century’, (eds. HooJ. J. C.), 152–166; 1998, West Conshohocken, PA, ASTM.
89.
VoskampA. P. and MittemeijerE. J.: ‘State of residual stress induced by cyclic rolling contact loading’, J. Mater. Sci. Technol., 1997, 13, (5), 430–438. doi: 10.1179/mst.1997.13.5.430
90.
KotzalasM. N. and DollG. L.: ‘Tribological advancements for reliable wind turbine performance’, Philos. Trans. R. Soc. Lond. Ser. A: Math. Phys. Eng. Sci., 2010, 368, (1929), 4829–4850. doi: 10.1098/rsta.2010.0194
91.
WoodR. J. K., BahajA. S., TurnockS. R., WangL. and EvansM.: ‘Tribological design constraints of marine renewable energy systems’, Philos. Trans. R. Soc. A: Math. Phys. Eng. Sci., 2010, 368, (1929), 4807–4827. doi: 10.1098/rsta.2010.0192
92.
EvansM.-H., RichardsonA. D., WangL., WoodR. J. K., and AndersonW. B.: ‘Confirming subsurface initiation at non-metallic inclusions as one mechanism for white etching crack (WEC) formation’, Wear, 2014, 75, 87–97, Reprinted from Wear with permission from Elsevier. Copyright (2014).
93.
ŠčepanskisM., JakovičsA., KaldreI., HolwegerW., NackeB., DiederichsA.: ‘The numerical model of electrothermal deformations of carbides in bearing steel as the possible cause of white etching cracks initiation’, Tribol. Lett., 59, 2015, 1–10. Fig. 1.
94.
Solano-AlvarezW., BhadeshiaH. K. D. H.: ‘White-etching matter in bearing steel. Part II: distinguishing cause and effect in bearing steel failure’, Metallur. Mater. Trans. A, 45, 2014, 4916–4931. Figs. 4 and 8. doi: 10.1007/s11661-014-2431-x
95.
StiénonA., FazekasA., BuffièreJ. Y., VincentA., DaguierP. and MerchiF.: ‘A new methodology based on X-ray micro-tomography to estimate stress concentrations around inclusions in high strength steels’, Mater. Sci. Eng. A, 2009, 513–514, 376–383. doi: 10.1016/j.msea.2009.02.008
96.
HolwegerW.: Personal communication, 2015.
97.
GegnerJ. and NierlichW.: ‘Operational residual stress formation in vibration-loaded rolling contact’, Adv. X-ray Anal., 2008, 52, 722–731.
98.
GrabulovA., ZieseU. and ZandbergenH. W.: ‘TEM/SEM investigation of microstructural changes within the white etching area under rolling contact fatigue and 3-D crack reconstruction by focused ion beam’, Scr. Mater., 2007, 57, (7), 635–638. doi: 10.1016/j.scriptamat.2007.06.024
99.
HaradaH., MikamiT., ShibataM., SokaiD., YamamotoA. and TsubakinoH.: ‘Microstructural changes and crack initiation with white etching area formation under rolling/sliding contact in bearing steel’, ISIJ Int., 2005, 45, (12), 1897–1902. doi: 10.2355/isijinternational.45.1897
100.
MurogaA. and SakaH.: ‘Analysis of rolling contact fatigued microstructure using focused ion beam sputtering and transmission electron microscopy observation’, Scr. Metallur. Mater., 1995, 33, (1), 151–156. doi: 10.1016/0956-716X(95)00108-8
101.
GrabulovA.: ‘Fundamentals of rolling contact fatigue’, PhD thesis, University of Belgrade, Serbia, 2010.
102.
BuchwaldJ. and HeckelH. W.: ‘An analysis of microstructural changes in 52100 steel bearings due to cyclic stressing’, Trans. ASM, 1968, 61, 750–756.
MartinJ. A., BorgeseS. F. and EberhardtA. D.: ‘Microstructural alterations of rolling bearing steels undergoing cyclic stressing’, J. Basic Eng., 1966, 88, 555–567. doi: 10.1115/1.3645902
105.
MurakamiY., NakaM., IwamotoA. and ChatellG.: ‘Long life bearings for automotive alternator applications’, International congress and exposition, Detroit, MI, 27 February–2 March, 1995, SAE International, 1–14.
106.
VincentA., LormandG., LamagnèreP., GossetL., GirodinD., DudragneG. and FougèresR.: ‘From white etching areas formed around inclusions to crack nucleation in bearing steels under rolling contact fatigue’ in ‘Bearing steels: into the 21st Century’, (eds. HooJ. J. C.), 109–123; 1998, West Conshohocken, PA, ASTM.
107.
HiraokaK., FujimatsuT., TsunekageN. and YamamotoA.: ‘Generation process observation of micro-structural change in rolling contact fatigue by hydrogen-charged specimens’, Jpn. J. Tribol., 2007, 52, (6), 673–683.
108.
SchlichtH., SchreiberE. and ZwirleinO.: ‘Effects of material properties on bearing steel fatigue strength’ in ‘Effect of steel manufacturing processes on the quality of bearing steels’, (ed. HooJ. J. C.), 81–101; 1988, Philadelphia, ASTM.
109.
BöhmK., SchlichtH., ZwirleinO. and EberhardR.: ‘Nonmetallic inclusions and rolling contact fatigue’ in ‘Bearing steels: the rating of nonmetallic inclusions’, 96–113; 1974, Boston, MA, USA, ASTM.
110.
ShibataM.: ‘Trends of studies on rolling contact fatigue life and recent results’, Koyo Eng. J. Engl. Ed., 2004, 164E, 8–13.
111.
FörstC., SlyckeJ., Van VlietK. and YipS.: ‘Point defect concentrations in metastable Fe-C alloys’, Phys. Rev. Lett., 2006, 96, (17), 175501. doi: 10.1103/PhysRevLett.96.175501
112.
HiraokaK., NagaoM. and IsomotoT.: ‘Study on flaking process in bearings by white etching area generation’, J. ASTM Int., 2006, 3, (5), 1–7. doi: 10.1520/JAI14059
113.
VegterR. H. and SlyckeJ. T.: ‘The role of hydrogen on rolling contact fatigue response of rolling element bearings’, J. ASTM Int., 2009, 7, (2), 1–12.
114.
PrashadH.: ‘Tribology in electrical environments’; 2005, Amsterdam, Elsevier Science.
115.
EvansM.-H., WalkerJ. C., MaC., WangL., WoodR. J. K., ‘A FIB/TEM study of butterfly crack formation and white etching area (WEA) microstructural changes under rolling contact fatigue in 100Cr6 bearing steel’, Mater. Sci. Eng. A, 2013, 570, 127–134. Copyright (2013) with permission from Elsevier.
116.
EvansM.-H., WangL., JonesH., and WoodR. J. K., ‘White etching crack (WEC) investigation by serial sectioning, focused ion beam and 3-D crack modelling’, Tribol. Int.146–160. Reprinted from Tribology International. Copyright (2013) with permission from Elsevier.
WestO. H. E., DiederichsA. M., AlimadadiH., DahlK. V., and SomersM. A. J.: ‘Application of complementary techniques for advanced characterization of white etching cracks’, Pract. Metallogr., 2013, 50, 410–431. doi: 10.3139/147.110246
119.
PressouyreG. M.: ‘A classification of hydrogen traps in steel’, Metall. Trans. A, 1979, 10, 1571–1573. doi: 10.1007/BF02812023
120.
Printed with permission of the copyright holder, the American Gear Manufacturers Association, 1001 N. Fairfax Street, 5th Floor, Alexandria, Virginia 22314. Statements presented in this paper are those of the authors and may not represent the position or opinion of the American Gear Manufacturers Association.
121.
ErrichelloR., BudnyR. and EckertR.: ‘Investigations of bearing failures associated with white etching areas (WEAs)’, Wind Turb. Gearboxes Tribol. Trans., 2013, 56, 1069–1076. Reprinted by permission of the publisher (Taylor & Francis Ltd, http://www.tandfonline.com). doi: 10.1080/10402004.2013.823531
122.
Reprinted with permission: from the ASTM 1580 Bearing Steel Technologies: 10th Volume, copyright ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428.
123.
Argonne National Laboratory: managed and operated by UChicago Argonne, LLC, for the U.S. Department of Energy under Contract No. DE-AC02-06CH11357.
124.
LundT. B.: ‘Subsurface initiated rolling contact fatigue - influence of non-metallic inclusions, processing conditions, and operating conditions’, J. ASTM Int., 2010, 7, (5), 1–12. doi: 10.1520/JAI102559
125.
SuginoK., MiyamotoK., NagumoM. and AokiK.: ‘Structural alterations of bearing steels under rolling contact fatigue’, ISIJ Int., 1970, 10, 98–111.
126.
O'BrienJ. L. and KingA. H.: ‘Electron microscopy of stress-induced structural alterations near inclusions in bearing steels’, J. Basic Eng., 1966, 568–572. doi: 10.1115/1.3645907
127.
TricotR., MonnotJ. and LluansiM.: ‘How microstructural alterations affect fatigue properties of 52100 steel’, Met. Eng. Q., 1972, 12, (2), 39–47.
128.
HydeR. S.: ‘Microstructural changes from contact fatigue’ in ‘ASM handbook–Vol. 19 fatigue and fracture’ 1749–1780; 1996, OH, ASM International.
129.
BrücknerM., GegnerJ., GrabulovA., NierlichW. and SlyckeJ.: ‘Alternative butterfly formation mechanisms in rolling contact fatigue’, ‘5th international conference on very high cycle fatigue’, Berlin, Germany, June 28–30, 2011, 138–151.
130.
JohnsonR. F. and BlankJ. R.: ‘Fatigue in rolling contact: some metallurgical aspects’, Proc. Inst. Mech. Eng., 1963, 95–102.
131.
DaviesW. J. and DayK. L.: ‘Surface fatigue in ball bearings, roller bearings, and gears in aircraft engines’, Symposium: fatigue in rolling contact, instn. mech. engrs., London, UK, 1963, Instn. Mech. Engrs., 23–40.
132.
UmezawaO. and NagaiK.: ‘Effects of test temperature on internal fatigue crack generation associated with nonmetallic particles in austenitic steels’, Metall. Mater. Trans. A, 1998, 29, 3017–3028. doi: 10.1007/s11661-998-0209-8
133.
MayerH., HaydnW., SchullerR., IsslerS. and Bacher-HöchstM.: ‘Very high cycle fatigue properties of bainitic high carbon–chromium steel under variable amplitude conditions’, Int. J. Fatigue, 2009, 31, (8–9), 1300–1308. doi: 10.1016/j.ijfatigue.2009.02.038
134.
BrooksbankD. and AndrewsK. W.: ‘Stress fields around inclusions and their relation to mechanical properties’, J. Iron Steel Inst. (Lond.), 1971, 210, 246–255.
135.
HashimotoK., FujimatsuT., TsunekageN., HiraokaK., KidaK. and SantosE. C.: ‘Study of rolling contact fatigue of bearing steels in relation to various oxide inclusions’, Mater. Des., 2011, 32, (3), 1605–1611. doi: 10.1016/j.matdes.2010.08.052
136.
HashimotoK., FujimatsuT., TsunekageN., HiraokaK., KidaK. and SantosE. C.: ‘Effect of inclusion/matrix interface cavities on internal-fracture-type rolling contact fatigue life', Mater. Des., 2011, 32, (10), 4980–4985. doi: 10.1016/j.matdes.2011.06.056
137.
HarrisT. A. and KotzalasM. N.: ‘Rolling bearing analysis—essential concepts of bearing technology’; 2007, Boca Raton, FL, US, Taylor & Francis.
138.
SureshS.: ‘Fatigue of materials’; 1991, Cambridge, Cambridge University Press.
139.
DieterG. E.: ‘Mechanical metallurgy’; 1986, New York, McGraw-Hill.
140.
KinoN. and OtaniK.: ‘The influence of hydrogen on rolling contact fatigue life and its improvement’, JSAE Rev., 2003, 24, (3), 289–294. doi: 10.1016/S0389-4304(03)00035-3
141.
Bruker: ‘Application note: hydrogen determination in high strength steel’, 2011, Bruker Elemental GmbH, 12.
142.
MurakamiY. and MatsunagaH.: ‘The effect of hydrogen on fatigue properties of steels used for fuel cell system’, Int. J. Fatigue, 2006, 28, (11), 1509–1520. doi: 10.1016/j.ijfatigue.2005.06.059
143.
CirunaJ. A. and SzieleitH. J.: ‘The effect of hydrogen on the rolling contact fatigue life of AISI 52100 and 440C steel balls’, Wear, 1973, 24, 107–118. doi: 10.1016/0043-1648(73)90207-X
144.
GrunbergL., JamiesonD. T. and ScottD.: ‘Hydrogen penetration in water-accelerated fatigue of rolling surfaces’, Philos. Mag., 1963, 8, (93), 1553–1568. doi: 10.1080/14786436308207318
145.
NagumoM., NakamuraM. and TakaiK.: ‘Hydrogen thermal desorption relevent to delayed-fracture susceptibility of high-strength steels’, Metall. Mater. Trans. A, 2001, 32, 339–347. doi: 10.1007/s11661-001-0265-9
146.
NagumoM.: ‘Hydrogen related failure of steels – a new aspect’, J. Mater. Sci. Technol., 2004, 20, 940–950. doi: 10.1179/026708304225019687
147.
TakaiK., ShodaH., SuzukiH. and NagumoM.: ‘Lattice defects dominating hydrogen-related failure of metals’, Acta Mater., 2008, 56, (18), 5158–5167. doi: 10.1016/j.actamat.2008.06.031
148.
MatsubaraY. and HamadaH.: ‘A novel method to evaluate the influence of hydrogen on fatigue properties of high strength steels’, J. ASTM Int., 2006, 3, (2), 1–14. doi: 10.1520/JAI14048
149.
HirthJ. P.: ‘Effects of hydrogen on the properties of iron and steel’, Metall. Trans. A, 1980, 11, 861–890. doi: 10.1007/BF02654700
150.
OtsukaT., HanadaH., NakashimaH., SakamotoK., HayakawaM., HashizumeK. and SugisakiM.: ‘Observation of hydrogen distribution around non-metallic inclusions in steels with tritium microautoradiography’, Fusion Sci. Technol., 2005, 48, (1), 708–711.
151.
WaltonH. W.: ‘Ubiquitous hydrogen’, 19th ASM heat treating society proceedings including steel heat treating in the new millennium, Cincinnati, OH, US, November 1–4, 1999, ASM, 558–563.
152.
EnomotoM., HirakamiD. and TaruiT.: ‘Thermal desorption analysis of hydrogen in high strength martensitic steels’, Metall. Mater. Trans. A., 2012, 43, 572. doi: 10.1007/s11661-011-0909-3
153.
ParkD., MaroefI. S., LandauA. and OlsonD. L.: ‘Retained austenite as a hydrogen trap in steel welds’, Weld. J., 2002, 27–35.
154.
TanakaS. and MurakamiY.: ‘Rolling bearing’, Patent, US, 2008.
155.
Solano-AlvarezW., SongE., HanD., SuhD.-W. and BhadeshiaH. K. D. H.: ‘Cracks in martensite plates as hydrogen traps in a bearing steel’, Metall. Mater. Trans. A, 2015, 46, (2), 665–673. doi: 10.1007/s11661-014-2680-8
156.
BirnbaumH. K. and SofronisP.: ‘Hydrogen-enhanced localized plasticity - a mechanism for hydrogen related failure’, Mater. Sci. Eng. A, 1994, 176, (1–2), 191–202. doi: 10.1016/0921-5093(94)90975-X
FujitaS., MatsuokaS., MurakamiY. and MarquisG.: ‘Effect of hydrogen on mode II fatigue crack behavior of tempered bearing steel and microstructural changes’, Int. J. Fatigue, 2010, 32, (6), 943–951. doi: 10.1016/j.ijfatigue.2009.06.005
159.
MurakamiY., KanezakiT., MineY. and MatsuokaS.: ‘Hydrogen embrittlement mechanism in fatigue of austenitic stainless steels’, Metall. Mater. Trans. A, 2008, 39, (6), 1327–1339. doi: 10.1007/s11661-008-9506-5
160.
ĆwiekJ.: ‘Hydrogen degradation of high-strength steels’, J. Achiev. Mater. Manuf. Eng., 2009, 37, 193–212.
KoharaM., KawamuraT. and EgamiM.: ‘Study on mechanism of hydrogen generation from lubricants’, Tribol. Trans., 2006, 49, (1), 53–60. doi: 10.1080/05698190500486324
163.
IsoK., YokouchiA. and TakemuraH.: ‘Research work for clarifying the mechanism of white structure flaking and extending the life of bearings’, SAE World Congress, Detroit, MI, April 11–14, 2005, SAE International.
164.
NSK: ‘Long life bearings for engine accessories’, Motion Control, 2004, NSK, 1–10.
165.
TamadaK. and TanakaH.: ‘Occurrence of brittle flaking on bearings used for automotive electrical instruments and auxiliary devices’, Wear, 1996, 199, (2), 245–252. doi: 10.1016/0043-1648(96)06990-6
166.
UyamaH., YamadaH., HidakaH. and MitamuraN.: ‘The effects of hydrogen on microstructural change and surface originated flaking in rolling contact fatigue’, Tribol. Online, 2011, 6, (2), 123–132. doi: 10.2474/trol.6.123
167.
IsoK., MiyajimaH., DenpouK., TodaY., YamazakiM., NakaM. and FujitaY.: ‘Rolling bearing, rolling bearing for fuel cell, compressor for fuel cell system and fuel cell system’, Patent, US,2007.
168.
UmedaA., ShigaT. and IhataK.: ‘Rolling bearing incorporated in auxiliary device for internal combustion engine’, Patent, US,2009.
169.
MikamiH. and KawamuraT.: Influence of electrical current on bearing flaking life, in SAE Technical Paper. 2007, SAE International.
170.
EndoT., DongD., ImaiY. and YamamotoY.: ‘Study on rolling contact fatigue in hydrogen atmosphere–improvement of rolling contact fatigue life by formation of surface film’, Life cycle tribology, 31st Leeds-Lyon tribology symposium, Trinity and All Saints College, Leeds, UK, September 7–10, 2004, Elsevier, 343–350.
171.
ThompsonA. and BernsteinI. M.: ‘The role of metallurgical variables in hydrogen-assisted environmental fracture’ in ‘Advances in corrosion science and technology’, (ed. FontanaM. G. et al.), 53–175; 1980, NY, Plenum Press.
172.
ListonT. V.: ‘Engine lubricant additives - what they are and how they function’, Lubr. Eng., 1992, 48, (5), 389–397.
173.
CantleyR. E.: ‘The effect of water in lubricating oil on bearing fatigue life’, ASLE Trans., 1977, 20, (3), 244–248. doi: 10.1080/05698197708982838
174.
MatsumotoY., MurakamiY. and OohoriM.: ‘Rolling contact fatigue under water-infiltrated lubrication’ in ‘Bearing steel technology’, (ed. BeswickJ. M.), 226–243; 2002, West Conshohocken, PA, ASTM International.
175.
SchatzbergP.: ‘Inhibition of water-accelerated rolling-contact fatigue’, J. Lubr. Technol., 1971, 70, 231–233. doi: 10.1115/1.3451546
176.
SchatzbergP. and FelsenI. M.: ‘Effects of water and oxygen during rolling contact lubrication’, Wear, 1968, 12, (5), 331–342. doi: 10.1016/0043-1648(68)90536-X
177.
SullivanJ. L. and MiddletonM. R.: ‘The pitting and cracking of SAE 52100 steel in rolling/sliding contact in the presence of an aqueous lubricant’, ASLE Trans., 1985, 28, (4), 431–438. doi: 10.1080/05698198508981640
178.
BrizmerV., PasaribuH. R. and Morales-EspejelG. E.: ‘Micropitting performance of oil additives in lubricated rolling contacts’, Tribol. Trans., 2013, 56, (5), 739–748. doi: 10.1080/10402004.2013.790097
179.
FitchJ.: How water causes bearing failure. Machinery Lubrication Magazine. 2008.
HamrockB. J. and DowsonD.: ‘Ball bearing lubrication: the elasto hydrodynamics of elliptical contacts’; 1981, New York, John Wiley.
182.
StachowiakG. W. and BatchelorA. W.: ‘Engineering tribology’, 801; 2006, Oxford, UK, Elsevier Butterworth-Heinemann.
183.
WrightT. W.: ‘The physics and mathematic of adiabatic shear bands’; 2002, Cambridge, UK, Cambridge University Press.
184.
WalleyS. M.: ‘Shear localization: A historical overview’, Metall. Mater. Trans. A, 2007, 38, (11), 2629–2654. doi: 10.1007/s11661-007-9271-x
185.
WhittleM., TrevelyanJ. and TavnerP. J.: ‘Bearing currents in wind turbine generators’, J. Renew. Sustain. Energy, 2013, 5, (5), 053128. doi: 10.1063/1.4822048
186.
KangY. S., EvansR. D. and DollG. L.: ‘Roller-raceway slip simulations of wind turbine gearbox bearings using dynamic bearing model’, STLE/ASME 2010 international joint tribology conference, San Francisco, CA, USA, October 17–20, 2010, ASME, 407–409.
187.
TanakaS., MitamuraN. and MurakamiY.: ‘Influence of sliding and chromium content in the steel on the white structural change under rolling contact’, Proceedings of the global powertrain conference, Dearborn, MI, September 28–30, 2004, 6–13.
188.
FujitaS., MitamuraN. and MurakamiY.: ‘Research of new factors affecting rolling contact fatigue life’ in ‘World tribology congress III’, 1–2; September 12–16, 2005, Washington, DC, ASME.
189.
EvansR. D., DollG. L., HagerC. H. and HoweJ. Y.: ‘Influence of steel type on the propensity for tribochemical wear in boundary lubrication with a wind turbine gear oil’, Tribol. Lett., 2010, 38, (1), 25–32. doi: 10.1007/s11249-009-9565-9
190.
TamadaK., TanakaH. and TsushimaN.: ‘A new type of flaking failure in bearings for electrical instruments of automotive engines’ in ‘Bearing steels: into the 21st century’, (ed. HooJ. J. C.), Medium: X; Size: 167–188; 1998, West Conshohocken, American Society for Testing and Materials.
191.
OswaldF. B., ZaretskyE. V. and PoplawskiJ. V.: ‘Interference-fit life factors for roller bearings’, Tribol. Trans., 2009, 52, (4), 415–426. doi: 10.1080/10402000802687890
192.
OswaldF. B., ZaretskyE. V. and PoplawskiJ. V.: ‘Interference-fit life factors for ball bearings’, Tribol. Trans., 2010, 54, (1), 1–20. doi: 10.1080/10402004.2010.512428
193.
DaguierP., RoeschO. and WernerT.: ‘New development in through hardened bearing steel grades for use in contaminated lubrication’, J. ASTM Int., 2006, 3, (6), 131–139. doi: 10.1520/JAI14045
194.
BohmerH.-J., HirschT. and StreitE.: ‘Rolling contact fatigue behaviour of heat resistant bearing steels at high operational temperatures’, J. ASTM Int., 1998, STP 1327, 131–151.
195.
ParkerR. J. and HodderR. S.: ‘Effect of double vacuum melting and retained austenite on rolling-element fatigue life of AMS5749 bearing steel’, NASA, 1977, 1060, 1–14.
196.
FurumuraK., MurakamiY. and AbeT.: ‘Case-hardening medium carbon steel for tough and long life bearing under severe lubrication conditions’ in ‘Bearing steels: into the 21st century’, (ed. HooJ. J. C.), 1998, West Conshohocken, American Society for Testing and Materials.
197.
TrojahnW., StreitE., ChinH. A. and EhlertD.: ‘Progress in bearing performance of advanced nitrogen alloyed stainless steel, Cronidur 30’, Materialwissenschaft und Werkstofftechnik, 1999, 30, (10), 605–611. doi: 10.1002/(SICI)1521-4052(199910)30:10<605::AID-MAWE605>3.0.CO;2-V
NygaardJ. R., RawsonM., DansonP. and BhadeshiaH. K. D. H.: ‘Bearing steel microstructures after aircraft gas turbine engine service’, J. Mater. Sci. Technol., 2014, 30, (15), 1911–1918. doi: 10.1179/1743284714Y.0000000548
200.
XiangduoP., ShimizuY. and MitamuraN.: ‘Long life bearing technologies on material aspect’ in ‘Advanced tribology’, (ed. LuoJ. et al.), 932–933; 2010, Berlin, Heidelberg, Springer.
201.
LuyckxJ., BroedersW. and GeertsomJ.: ‘Method for increasing the fatigue strength of a predominantly steel mechanical part of a wind turbine and/or for reducing the tendency to form what are called “white etching cracks” or “brittle flakes” in such steel mechanical parts’, Patent, US, 2009.
202.
GegnerJ., SchlierL. and NierlichW.: ‘Evidence and analysis of thermal static strain aging in the deformed surface zone of finish-machined hardened steel’, Powder Diffrac., 2009, 24, (S1), 45–50. doi: 10.1154/1.3133133
203.
GegnerJ.: ‘Post-machining thermal treatment (PMTT) of hardened rolling bearing steel’, 4th international conference on ‘mathematical modeling and computer simulation of material technologies’, College of Judea and Samaria, Ariel, Israel, 2006, 66–75.
204.
GebauerR. and RuhlS.: ‘Rolling bearings in wind turbine gearboxes’, 2003, Herzogenaurach, INA Wälzlager Schaeffler oHG. Sach-Nr. 010-119-159/WWG US-D 04012.
205.
EvansR. D., HagerC. H. and LogsdonR. D.: ‘Friction and wear performance of candidate surface treatments for wind turbine gearbox bearings in high slip contacts’, ASME/STLE 2009 international joint tribology conference, Memphis, TN, October 19–21, 2009, 491–493.
SongR.-H., PyunS.-I. and OrianiR. A.: ‘The hydrogen permeation through passivating film on iron by modulation method’, Electrochim. Acta, 1991, 36, (5), 825–831. doi: 10.1016/0013-4686(91)85280-K
208.
BrizmerV., RychahivskyyA. and HanB.: ‘Study on anti-micropitting performance of black oxide coating’, World Tribol. Congr., 2013, Turin.
209.
Reprinted with permission from the STP1542 Rolling Element Bearings, copyright ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428.
