Abstract
The purpose of this paper is to review corrosion processes and experience related to coal-fired gas turbines. For over 40 years there have been major programmes of research directed towards burning coal in a gas turbine either directly or as a coal-derived fuel. This history is briefly reviewed, demonstrating the importance which corrosion of the hot section has had in limiting the achievements and defining the systems. The probable corrosion mechanisms are identified, and because of their synergistic interaction with corrosion, erosion and deposition are also considered. The discussion identifies pressurized fluidized bed combustion (PFBC) as the direct combustion technique most likely to be able to avoid serious corrosion problems in the immediate future. Recent results from PFBC pilot plant investigations related to turbine materials are compared, and thereby future directions for overcoming corrosion problems are proposed. MST/449
Get full access to this article
View all access options for this article.
References
1.
B. J. Davidson, D. B. Meadowcroft, and J. Stringer: in ‘High temperature alloys for gas turbines and other applications’, (ed. W. Betz et al. ), 219–244; 1986, Dordrecht, Reidel.
2.
S. Muskovitz, J. Mogal, and S. Wolasin: in Proc. 1st Conf. on ‘Advanced materials for alternative fuel capable directly fired heat engines’, (ed. J. W. Fairbanks and J. Stringer), 913–938; 1979, US Dept. of Energy/Electric Power Research Institute, CONF 790749.
3.
B. J. Davidson and J. Holmes: in ‘A comparative study of fluidized bed combustion concepts for power generation’, Vol. 1; 1983, Coal Technology Europe, Amsterdam, Elsevier.
4.
G. H. Meier and F. S. Pettit: paper presented at conf. on ‘High temperature corrosion of superalloys’, The Royal Society, London, Feb. 1986, The Institute of Metals.
5.
J. W. Laxton, D. B. Meadowcroft, F. Clarke, T. Flatley, and C. W. Morris: in ‘Control of fireside corrosion in power station boilers’, 3 edn; 1987, London, CEGB.
6.
W. H. Gibb: in ‘Corrosion resistant materials for coal conversion systems’, (ed. D. B. Meadowcroft and M. I. Manning), 25–45; 1983, London, Applied Science.
7.
H. S. SPACIL and K. L. Luthra: J. Electrochem. Soc. , 1982, 129 , (9), 2119–2126.
8.
R. L. McCarron, R. P. Brobst, D. R. Spriggs, and A. M. Beltran: Final Report to Electric Power Research Institute on Project RP 1337-1, Palo Alto, Cal., 1986.
9.
R. L. McCarron: ‘Corrosion and erosion in PFBC environments’, Electric Power Research Institute Report CS3363, Palo Alto, Cal., 1984.
10.
N. A. Burdett, B. J. Gliddon, R. C. Hotchkiss, and R. T. Squires: J. Inst. Energy, 1983, 56, 119–124.
11.
A. Cohn: ‘Workshop proceedings: direct coal fired gas turbines’, Electric Power Research Institute Report AP3939 SR, Palo Alto, Cal., 1985.
12.
J. R. Nicholls and D. J. Stephenson: paper presented at conf. on ‘High temperature corrosion of superalloys’, The Royal Society, London, Feb. 1986, The Institute of Metals.
13.
R. A. Wenglarz and W. Tabakoff: J. Test. Eval. , 1982, (11), 298–302.
14.
R. A. Wenglarz, M. A. Alvin, and S. J. Schneider: ‘Predictions of combustion turbine performance in pressurized fluidized bed combustion power plants’, Electric Power Research Institute Report CS 1845, Palo Alto, Cal., 1981.
15.
R. H. Barkalow, J. A. Goebel, and F. S. Pettit: ‘Materials problems in fluidized-bed combustion systems: High temperature erosion-corrosion by high velocity (200 ms−1) particles’, Electric Power Research Institute Report CS 1448, Palo Alto, Cal., 1980.
16.
R. H. Barkalow: ‘Erosion corrosion by high velocity particles in fluidized bed combustion systems’, Electric Power Research Institute Report CS3396, Palo Alto, Cal., 1984.
17.
S. R. J. Saunders, M. K. Hossain, and J. M. Ferguson: in ‘High temperature alloys for gas turbines 1982’, (ed. R. Brunetaud et al. ), 177–206; 1982, Dordrecht, Reidel.
18.
R. A. McCarron and D. A. Grey: ‘Materials problems in fluidized-bed combustion systems. Review of the information on gas turbine materials in coal combustion environments’, Electric Power Research Institute Report CS 1469, 1980.
19.
R. J. Stettler, A. H. Bell, and E. W. Shows: in Proc. Int. Conf. on ‘Gas turbines’, Mar. 1983, ASME, Paper 8–GT–183.
20.
L. K. Carpenter, F. W. Crowe, Jr, and J. S. Halow: in Proc. Int. Conf. on ‘Gas turbines’, Mar. 1985, ASME, Paper 85–GT–213.
21.
R. D. smith and G. L. Wade: in Proc. ‘Total Energy Conference’, Copenhagen, 122–158, 1976.
22.
‘Engineer design construct test and evaluate a pressurized fluidized bed pilot plant using high sulphur coal for production of electric power’, US DOE Contract No. EX-76-C-01-1726, Curtiss-Wright Corporation, 1976.
23.
G. R. Zellars, S. M. Benford, A. P. Rowe, and C E. Lowell: in Proc. 1st Conf. on ‘Advanced materials for alternative fuel capable directly fired heat engines’, (ed. J. W. Fairbanks and J. Stringer), 887–912; 1979, US Dept. of Energy/Electric Power Research Institute, CONF 790749.
24.
J. C. Galsworthy, J. E. Restall, and G. C. Booth: in ‘High temperature alloys for gas turbines’, (ed. R. Brunetaud et al. ), 207–236; 1982, Dordrecht, Reidel.
25.
K. K. Pillai, S. E. Kreij, and R. Paulsson: in Proc. 8th Int. Conf. on ‘Fluidized bed combustion’, Houston, Tex., US Dept. of Energy, Mar. 1985, METC-85/6021.
26.
S. A. Jansson, N. G. Nilssen, and B. O. Malon: in Proc. 6th Int. Conf. on ‘Fluidized bed combustion’, Atlanta, GA, Apr. 1980.
27.
R. L. McCarron and R. P. Brobst: in ‘Corrosion ‘84’, paper 92; 1984, Houston, Tex., National Association of Corrosion Engineers.
28.
J. Stringer, R. L. McCarron, A. M. Beltran, A. J. Minchener, J. S. Anderson, and R. A. Mountford: in Proc. 8th Int. Conf. on ‘Fluidized bed combustion’, Houston, Tex., US Dept. of Energy, Mar. 1985, METC-85/6021.
29.
W. Tabakoff: J. Fluid Eng. , 1984, 108, 125–134.
30.
P. J. Shayler and K. H. Yee: Wear, 1984, 98, 127–140.
31.
W. Goward: in Proc. Int. Conf. on ‘Gas turbines’, Mar. 1985, ASME, Paper 85-GT-60.
32.
W. Goward: Turbomachinery Int. , May–June 1985, 24–28.
33.
P. Hancock: Mater. Sci. Technol. , this issue, 536–544.
34.
T. E. Lippert, D. F. Ciliberti, O. J. Tassicker, and G. G. Drenker: in Proc. Conf. on ‘Gas cleaning at high temperatures’, Surrey, Sept. 1976, The Institution of Chemical Engineers, London, paper 15, pp. 215–232.