In this study, a novel W and TiO2 synergistic strengthened copper matrix nanocomposite was prepared by a powder metallurgy route with a mechano-chemical method and subsequent consolidation. Nano-sized W and TiO2 particles in the composite powder were fabricated by solid-phase reaction during the mechanical alloying procedure. The average sizes of W and TiO2 particles were only 51 and 171 nm, far finer than single-phase particle-strengthened composites. It was found that the nanoparticles effectively resisted the grain coarsening in the copper matrix, containing the grains with an average size of 350 nm. The ultimate tensile strength and electrical conductivity of the copper composite are 520 MPa and 74 IACS%, achieve an ideal trade-off between them. The observations suggested that the nanoparticles were highly uniformly dispersed in the copper matrix, and the particle coarsening was restrained as the results of the interaction effects between W and TiO2 nanoparticles.
CarroG, MuñozA, SavoiniB, Processing, microstructure and mechanical characterization of dispersion strengthened Cu-1%Y. Fusion Eng Des. 2019;138:321–331. https://doi.org/10.1016/j.fusengdes.2018.11.058.
4.
Abu-OqailA, WagihA, FathyA, Effect of high energy ball milling on strengthening of Cu-ZrO2 nanocomposites. Ceram Int. 2019;45:5866–5875. https://doi.org/10.1016/j.ceramint.2018.12.053.
5.
ZhengR, LiN.Mechanical properties and electrical conductivity of nano-La2O3 reinforced copper matrix composites fabricated by spark plasma sintering. Mater Res Express. 2019;6, https://doi.org/10.1088/2053-1591/ab36f7.
6.
AghamiriSMS, UkaiS, OonoN, Recrystallization of cold rolled oxide dispersion strengthened copper during room temperature annealing. J Alloys Compd. 2019;798:187–193. https://doi.org/10.1016/j.jallcom.2019.05.248.
7.
WagihA, Abu-OqailA, FathyA.Effect of GNPs content on thermal and mechanical properties of a novel hybrid Cu-Al2O3/GNPs coated Ag nanocomposite. Ceram Int. 2019;45:1115–1124. https://doi.org/10.1016/j.ceramint.2018.10.001.
8.
RenF, ZhiA, ZhangD, Preparation of Cu-Al2O3 bulk nano-composites by combining Cu-Al alloy sheets internal oxidation with hot extrusion. J Alloys Compd. 2015;633:323–328. https://doi.org/10.1016/j.jallcom.2015.02.057.
ZhuoH, TangJ, YeN.A novel approach for strengthening Cu-Y2O3 composites by in situ reaction at liquidus temperature. Mater Sci Eng A. 2013;584:1–6. https://doi.org/10.1016/j.msea.2013.07.007.
11.
RaghuT, SundaresanR, RamakrishnanP, Synthesis of nanocrystalline copper-tungsten alloys by mechanical alloying. Mater Sci Eng A. 2001;304–306:438–441. https://doi.org/10.1016/S0921-5093(00)01444-1.
12.
YoussefKM, AbazaMA, ScattergoodRO, High strength, ductility, and electrical conductivity of in-situ consolidated nanocrystalline Cu-1%Nb. Mater Sci Eng A. 2018;711:350–355. https://doi.org/10.1016/j.msea.2017.11.060.
13.
DarlingKA, RajagopalanM, KomarasamyM, Extreme creep resistance in a microstructurally stable nanocrystalline alloy. Nature. 2016;537:378–381. https://doi.org/10.1038/nature19313.
14.
ProsviryakovAS, BazlovAI.Characterization of nanostructured Cu-Cr bulk composites prepared by high-energy mechanical alloying. Mater Chem Phys. 2016;177:1–7. https://doi.org/10.1016/j.matchemphys.2016.03.047.
15.
XieZM, LiuR, MiaoS, Extraordinary high ductility/strength of the interface designed bulk W-ZrC alloy plate at relatively low temperature. Sci Rep. 2015;5:1–11. https://doi.org/10.1038/srep16014.
16.
WangR, XieZM, WangYK, Fabrication and characterization of nanocrystalline ODS-W via a dissolution-precipitation process. Int J Refract Met Hard Mater. 2019;80:104–113. https://doi.org/10.1016/j.ijrmhm.2019.01.002.
17.
GrozaJR, GibelingJC.Principles of particle selection for dispersion-strengthened copper. Mater Sci Eng A. 1993;171:115–125. https://doi.org/10.1016/0921-5093(93)90398-X.
18.
AtwaterMA, RoyD, DarlingKA, The thermal stability of nanocrystalline copper cryogenically milled with tungsten. Mater Sci Eng A. 2012;558:226–233. https://doi.org/10.1016/j.msea.2012.07.117.
19.
BahadorA, UmedaJ, HamzahE, Synergistic strengthening mechanisms of copper matrix composites with TiO2 nanoparticles. Mater Sci Eng A. 2020;772:138797, https://doi.org/10.1016/j.msea.2019.138797.
20.
IvanovE, SuryanarayanaC.Materials and process design through mechanochemical routes. J Mater Synth Process. 2000;8:235–244. https://doi.org/10.1023/A:1011372312172.
21.
BalciO, AǧaoǧullariD, SuryanarayanaC, Synthesis and characterization of vanadium boride powders and their sintered bodies. Mater Res Express. 2019;6, https://doi.org/10.1088/2053-1591/ab2e56.
ShehataF, FathyA, AbdelhameedM, Preparation and properties of Al2O3 nanoparticle reinforced copper matrix composites by in situ processing. Mater Des. 2009;30:2756–2762. https://doi.org/10.1016/j.matdes.2008.10.005.
24.
RyuSS, ParkHR, Do KimY, Effect of ball-milling time on structural characteristics and densification behavior of W-Cu composite powder produced from WO3-CuO powder mixtures. Int J Refract Met Hard Mater. 2017;65:39–44. https://doi.org/10.1016/j.ijrmhm.2016.11.012.
25.
SheibaniS, AtaieA, Heshmati-ManeshS.In-situ synthesis of Cu/Cr-Al2O3 nanocomposite by mechanical alloying and heat treatment. Metall Mater Trans A Phys Metall Mater Sci. 2010;41:2606–2612. https://doi.org/10.1007/s11661-010-0281-8.
26.
SuryanarayanaC, Grant NortonM.X-Ray diffraction: a practical approach. New York (NY): Springer Science Business Media; 1998.
27.
MatteazziP, Le CaerG.Synthesis of nanocrystalline alumina-metal composites. J Am Ceram Soc. 1992;75:2749–2755.
28.
DongSJ, ZhouY, ShiYW, Formation of a TiB2-reinforced copper-based composite by mechanical alloying and hot pressing. Metall Mater Trans A Phys Metall Mater Sci. 2002;33:1275–1280. https://doi.org/10.1007/s11661-002-0228-9.
29.
WilliamsonGK, HallWH.X-ray line broadening from filed aluminum and wolfram. Acta Metall. 1953;1:22–31. https://doi.org/10.1016/0001-6160(53)90006-6.
30.
SuryanarayanaC, KochCC.Nanocrystalline materials – current research and future directions. Hyperfine Interact. 2000;130:5–44.
31.
WangKF, SunGD, WuYD, Fabrication of ultrafine and high-purity tungsten carbide powders via a carbothermic reduction–carburization process. J Alloys Compd. 2019;784:362–369. https://doi.org/10.1016/j.jallcom.2019.01.055.
32.
KimDG, OhST, JeonH, Hydrogen-reduction behavior and microstructural characteristics of WO3-CuO powder mixtures with various milling time. J Alloys Compd. 2003;354:239–242. https://doi.org/10.1016/S0925-8388(03)00007-0.
33.
LuT, ChenC, GuoZ, Tungsten nanoparticle-strengthened copper composite prepared by a sol-gel method and in-situ reaction. Int J Miner Metall Mater. 2019;26:1477–1483. https://doi.org/10.1007/s12613-019-1889-3.
34.
KojuRK, DarlingKA, KecskesLJ, Zener pinning of grain boundaries and structural stability of immiscible alloys. Jom. 2016;68:1596–1604. https://doi.org/10.1007/s11837-016-1899-9.
MorrisDG, MorrisMA.Mechanical alloying of copper-BCC element mixtures. Scr Metall. Mater. 1990;24:1701–1706. https://doi.org/10.1016/0956-716X(90)90532-L.
LiC, ZhouY, XieY, Effects of milling time and sintering temperature on structural evolution, densification behavior and properties of a W-20wt.%Cu alloy. J Alloys Compd. 2018;731:537–545. https://doi.org/10.1016/j.jallcom.2017.10.081.
39.
SrivatsanT, NarendraN, TroxellJ.Tensile deformation and fracture behavior of an oxide dispersion strengthened copper alloy. Mater Des. 2000;21:191–198. https://doi.org/10.1016/S0261-3069(99)00096-5.
40.
HallEO.The deformation and aging of mild steel: II characteristics of the luders deformation. Proc Phys Soc London. 1951;B64:747. https://doi.org/10.1088/0370-1301/64/9/302.
41.
PetchNJ.The cleavage strength of polycrystals. J Iron & Steel Inst. 1953;174:25.
42.
HahnSI, HwangSJ.Estimate of the Hall-Petch and Orowan effects in the nanocrystalline Cu with Al2O3 dispersoid. J Alloys Compd. 2009;483:207–208. https://doi.org/10.1016/j.jallcom.2008.07.205.
43.
AnsellG, LenelF.Criteria for yielding of dispersion-strengthened alloys. Acta Metall. 1960;8:612–616. https://doi.org/10.1016/0001-6160(60)90015-8.
44.
Sanaty-ZadehA.Comparison between current models for the strength of particulate-reinforced metal matrix nanocomposites with emphasis on consideration of Hall-Petch effect. Mater Sci Eng A. 2012;531:112–118. https://doi.org/10.1016/j.msea.2011.10.043.
45.
ZhouD, GengH, ZengW, Effect of extrusion temperature on microstructure and properties of an ultrafine-grained Cu matrix nanocomposite fabricated by powder compact extrusion. J Mater. Sci. 2018;53:5389–5401. https://doi.org/10.1007/s10853-017-1952-2.
LuT, ChenC, LiP, Enhanced mechanical and electrical properties of in situ synthesized nano-tungsten dispersion-strengthened copper alloy. Mater Sci Eng A. 2021;799:140161. https://doi.org/10.1016/j.msea.2020.140161.
