Search results: Sage Journals

Restricted accessResearch articleFirst published May, 2012

Mechanical and dry sliding wear behavior of Al7075 alloy-reinforced with SiC particles

GB Veeresh Kumar, CSP Rao, N Selvaraj

Journal of Composite Materials

Restricted accessResearch articleFirst published May, 2024

Influence of aging process and reinforcement ratio on physical and mechanical properties of carbonized aramid reinforced Al7075 materials

Mehmet Emin Demir, Yahya Hışman Çelik, Ali Kalkanli

Proceedings of the Institution of Mechanical Engineers,Part C: Journal of Mechanical Engineering Science

Restricted accessReview articleFirst published June, 2025

Effects of inorganic reinforcements on microstructural,mechanical,tribological,and machining characteristics of stir cast Al7075 composite: A review

Randhir Kumar, Sharifuddin Mondal

Proceedings of the Institution of Mechanical Engineers,Part C: Journal of Mechanical Engineering Science

Restricted accessResearch articleFirst published September, 2015

Effect of densification rate on consolidation and properties of Al7075–B 4 C composite powder

G. H. Majzoobi, A. Atrian, M. K. Pipelzadeh

Powder Metallurgy

Restricted accessResearch articleFirst published 2025

Impact of machining parameters on surface roughness and machining forces in Al7075 turning with minimum quantity lubrication and cold fluid

Abbasali Bagheri, Vahid Abedini, Alireza Hajialimohamadi

Proceedings of the Institution of Mechanical Engineers,Part E: Journal of Process Mechanical Engineering

Restricted accessResearch articleFirst published 2026

Experimental investigation of Al7075 in computer numerical control drilling using Taguchi-based fuzzy-grey relational analysis optimization technique

Randhir Kumar, Sharifuddin Mondal

Proceedings of the Institution of Mechanical Engineers,Part E: Journal of Process Mechanical Engineering

Restricted accessResearch articleFirst published 2026

Effect of dual reinforcement and stir casting process parameters on the fretting wear response of Al7075–B 4 C–BFS hybrid composites

Prabina Kumar Patnaik, Srimant Kumar Mishra, Sasank Shekhar Panda

Proceedings of the Institution of Mechanical Engineers,Part E: Journal of Process Mechanical Engineering

Restricted accessResearch articleFirst published June, 2024

Measurement and analysis of radial force,radial torque and surface integrity in micro-drilling of an Al7075-T6 alloy

Shashank Shukla, Rahul Jain, Soumya Gangopadhyay

Proceedings of the Institution of Mechanical Engineers,Part B: Journal of Engineering Manufacture

Restricted accessResearch articleFirst published 2026

Microstructural,mechanical,and tribological evaluation of Al7075 reinforced with B4C and graphene particulates produced by stir casting

Rumalla Haranath, Koppanati Meera Saheb, Movva Naga Swapna Sri [...]

Journal of Composite Materials

Free accessResearch articleFirst published January, 2017

Trade-off among mechanical properties and energy consumption in multi-pass friction stir processing of Al7075 alloy employing neural network–based genetic optimization

G Hussain, M Ranjbar, S Hassanzadeh

Proceedings of the Institution of Mechanical Engineers,Part B: Journal of Engineering Manufacture

Restricted accessResearch articleFirst published May, 2012

Mechanical and dry sliding wear behavior of Al7075 alloy-reinforced with SiC particles

GB Veeresh Kumar, CSP Rao, N Selvaraj

Journal of Composite Materials

Restricted accessResearch articleFirst published May, 2024

Influence of aging process and reinforcement ratio on physical and mechanical properties of carbonized aramid reinforced Al7075 materials

Mehmet Emin Demir, Yahya Hışman Çelik, Ali Kalkanli

Proceedings of the Institution of Mechanical Engineers,Part C: Journal of Mechanical Engineering Science

Restricted accessReview articleFirst published June, 2025

Effects of inorganic reinforcements on microstructural,mechanical,tribological,and machining characteristics of stir cast Al7075 composite: A review

Randhir Kumar, Sharifuddin Mondal

Proceedings of the Institution of Mechanical Engineers,Part C: Journal of Mechanical Engineering Science

Restricted accessResearch articleFirst published September, 2015

Effect of densification rate on consolidation and properties of Al7075–B 4 C composite powder

G. H. Majzoobi, A. Atrian, M. K. Pipelzadeh

Powder Metallurgy

Restricted accessResearch articleFirst published 2025

Impact of machining parameters on surface roughness and machining forces in Al7075 turning with minimum quantity lubrication and cold fluid

Abbasali Bagheri, Vahid Abedini, Alireza Hajialimohamadi

Proceedings of the Institution of Mechanical Engineers,Part E: Journal of Process Mechanical Engineering

Restricted accessResearch articleFirst published 2026

Experimental investigation of Al7075 in computer numerical control drilling using Taguchi-based fuzzy-grey relational analysis optimization technique

Randhir Kumar, Sharifuddin Mondal

Proceedings of the Institution of Mechanical Engineers,Part E: Journal of Process Mechanical Engineering

Restricted accessResearch articleFirst published 2026

Effect of dual reinforcement and stir casting process parameters on the fretting wear response of Al7075–B 4 C–BFS hybrid composites

Prabina Kumar Patnaik, Srimant Kumar Mishra, Sasank Shekhar Panda

Proceedings of the Institution of Mechanical Engineers,Part E: Journal of Process Mechanical Engineering

Restricted accessResearch articleFirst published June, 2024

Measurement and analysis of radial force,radial torque and surface integrity in micro-drilling of an Al7075-T6 alloy

Shashank Shukla, Rahul Jain, Soumya Gangopadhyay

Proceedings of the Institution of Mechanical Engineers,Part B: Journal of Engineering Manufacture

Restricted accessResearch articleFirst published 2026

Microstructural,mechanical,and tribological evaluation of Al7075 reinforced with B4C and graphene particulates produced by stir casting

Rumalla Haranath, Koppanati Meera Saheb, Movva Naga Swapna Sri [...]

Journal of Composite Materials

Free accessResearch articleFirst published January, 2017

Trade-off among mechanical properties and energy consumption in multi-pass friction stir processing of Al7075 alloy employing neural network–based genetic optimization

G Hussain, M Ranjbar, S Hassanzadeh

Proceedings of the Institution of Mechanical Engineers,Part B: Journal of Engineering Manufacture